A blown fuse in your house can mean a one-off overload, or a wiring fault that will come back. In a Lalor home in July 2026, a blown fuse led us to a reverse polarity fault, deteriorated old wiring and a switchboard without modern protection. We fixed what was safe that evening and recommended a rewire and switchboard upgrade.

What does a blown fuse on an old switchboard mean?
It means the circuit hit a fault, a short circuit or too much load, and the fuse cut the power to protect it. A fuse that blows once after a toaster and a heater run together may be nothing more. A fuse that blows without an obvious reason, or blows again after you replace it, is a sign something on that circuit is wrong.
Older homes in Melbourne’s north often still have ceramic fuse boards. They do the basic job of cutting power, but they don’t give you the circuit breaker and safety switch protection we expect in a modern installation.
What we found on a real call-out in Lalor
Recent job: Lalor, ceramic fuse board and ageing wiring
On a Friday in July 2026 the owners lost power to one circuit and called us out after hours. Zach found the rewirable ceramic fuse for that circuit had blown. He swapped it for a suitably rated plug-in circuit breaker so he could reset the circuit safely while he tested it.
Testing, part of our fault finding process, showed a reverse polarity fault. The circuit fed a section that had been partly rewired earlier, so he isolated that section, corrected the fault and restored about half of the affected outlets. The remaining original wiring had deteriorated insulation and couldn’t be re-energised safely, so those outlets were left disconnected. He was on site for about 3 hours. We quoted $495 including GST, which allowed up to one hour of fault finding, and the invoice came to $669 including GST.

What is reverse polarity, and why does it matter?
Reverse polarity means the active and neutral wires are connected the wrong way around. Appliances can still seem to work, which is why it is easy to miss, but parts of an appliance that should be dead when it is switched off can stay live. It is a fault we fix before a circuit goes back into service. It is not something to test or fix yourself.
Why were some power points left disconnected?
Because switching them back on wasn’t safe. The original cabling on that part of the circuit had deteriorated insulation, and we couldn’t be sure of its integrity. We left those outlets disconnected rather than risk electric shock or fire, and we told the owners plainly.
If we can only restore part of a circuit, we say so on the night. A half-fixed circuit that looks fine is worse than one we have clearly marked off.
Why did we recommend a rewire and a switchboard upgrade?
A plug-in circuit breaker is better protection than a fuse, but it was a safe stopgap. It wasn’t a fix for the real problem. Much of the wiring in the home was old, showed signs of deterioration and didn’t meet current standards. The condition of the cabling also made the fault hard to trace, which tells you how reliable it is likely to be. We recommended:
-
A full rewire. More faults and power interruptions were likely until it was done. See our house rewiring service and our guide to the signs your home needs rewiring.
-
A full switchboard upgrade. A ceramic fuse board lacks the circuit breaker and safety switch protection of a modern board. See our switchboard upgrades and what affects the cost of a switchboard upgrade.
Not every old house needs a full rewire. This one did because of the age and condition of the wiring we could see, plus the fault itself.
What happened after the call-out?
The next morning Zach quoted the rewire and switchboard upgrade. The quote recorded deteriorated insulation on the majority of the cabling and allowed 40 hours of electrician time and 40 hours of apprentice time, for $14,300 including GST. Until work like this is done, more faults and power interruptions are likely, and parts of the installation may stay unsafe to switch on.
Power out and not sure why? Based in Thomastown, we work across Melbourne, and our emergency electricians are on call day and night. Call 1300 635 294.
What does it cost?
Prices include GST and are based on our recent jobs and quotes. Your price depends on the home, the access and what we find.
- After-hours call-out with fault finding: from $495, which covers up to one hour of fault finding. The Lalor job ran about 3 hours and came to $669.
- Full rewire with a new switchboard: our recent quotes for standard houses with wall cavity access have ranged from about $14,300 to $16,350. That included the new switchboard, smoke alarms, an independent inspection and a Certificate of Electrical Safety.
- Switchboard upgrade on its own: quoted after we inspect the board, because it depends on the board, the circuits and the wiring behind it. See our switchboard cost guide.
What should you do if a fuse blows at home?
Switch off or unplug the appliances on that circuit, then call a licensed electrician. Don’t keep resetting or replacing the fuse. If it blows again, there is a reason, and the reason might be in the walls. In Victoria, electrical work must be done by a licensed electrician, and Energy Safe Victoria says electrical work isn’t a DIY job (checked November 2026).
What to expect when we come out
We start at the switchboard, then test the affected circuit to find the fault. We make the circuit safe first, then explain what we found and what we recommend, in plain English. Any larger repair is quoted separately before we start, so you know the cost before you decide. If part of the home can’t be made safe that night, we tell you which part and why.
Frequently asked questions
Why does my fuse keep blowing?
A fuse blows when a circuit has a fault, a short circuit or too much load. If it blows again after you replace it, the cause still needs finding. On the Lalor job it was a reverse polarity fault in a home with ageing wiring.
Is an old fuse box unsafe?
A board with rewirable fuses doesn’t have the circuit breaker and safety switch protection of a modern board. Whether yours needs replacing depends on the board and the wiring behind it, which an electrician has to check.
Can a plug-in circuit breaker replace a rewirable fuse?
Yes, and it gives better protection than the fuse. On the Lalor job we fitted one so the circuit could be tested safely, but we still recommended a full switchboard upgrade.
Do I need a full rewire if one circuit fails?
Not always. In the Lalor home we recommended one because much of the wiring was old and deteriorated, and the fault was hard to trace through it.
How much does it cost to fix a blown fuse?
On our recent after-hours call-outs, the price started at $495 including GST, which covers up to one hour of fault finding. A longer job costs more: the Lalor call-out ran about 3 hours and came to $669. If the fault is in the wiring or the board, we quote that repair separately before we start.
Do you attend after hours?
Yes. Our emergency electricians are on call day and night.
Need an electrician for a blown fuse or an old switchboard?
Melbourne Wide Electrical is based in Thomastown and works across Melbourne, including Lalor. We are licensed and insured, with upfront fixed pricing and a lifetime guarantee on all work. Call 1300 635 294 or get a free quote.
Written by the Melbourne Wide Electrical team.


